Pengendalian Kualitas Produk Griller Menggunakan Failure Mode Effect and Analysis (FMEA) dan Root Cause Analysis (RCA)

Asma’ul Chusnah, Atikha Sidhi Cahyana

Abstract


A company engaged in the slaughterhouse of boiler chickens and one of its products is griller, which is chicken that is cut in a halal manner and packaged in the form of a whole carcass. Based on daily reports, the number of defects found in griller products shows a percentage of up to 30%. The purpose of this study is to identify the types of defects found in grillers so that alternative improvements can be determined. This research uses the Failure Mode Effect Analysis (FMEA) method to identify the most dominant types of defects in the product and find the causes. The highest defects from the FMEA results are processed by the Root Cause Analysis (RCA) method to provide improvement proposals so as to reduce the number of existing defects. The results of this study show that the most dominant type of defect is feathers remaining on the carcass with the highest RPN value of 175. The defect of feathers still remaining on the carcass is caused by workers who do not follow the SOP correctly, the changing size of raw materials, and rubber. The plucking machine is worn and loose, the settings of the plucking machine are loose, the temperature of the scalder tends to drop, the inspection in the process is not correct, there is no information on how to operate the machine, the raw materials are not uniform, and the working environment temperature is high and noisy.


Keywords


Quality Control; Chicken slaughtering industry; Failure Mode Effect Analysis; Root Cause Analysis

Full Text:

PDF

References


F. Y. Adiwijoyo and D. Purwanti, “ANALISIS PENAWARAN DAN PERMINTAAN DAGING AYAM RAS DI INDONESIA TAHUN 1984-2017: Kaitannya dengan Kenaikan Harga Domestik Daging Ayam Ras,” Semin. Nas. Off. Stat. 2019 Pengemb. Off. Stat. dalam mendukung Implementasi SDG’s, vol. 1, no. 2013, pp. 1155–1163, 2020.

D. S. Agusta and athika S. Cahyana, “Penentuan Komposisi yang Tepat Pembuatan Kerupuk Menggunakan Fault Tree Analysis dan Taguchi,” J. Saintek, vol. 13, no. 2, pp. 117–125, 2016, [Online]. Available: www.kopertis7.go.id,

I. Imron, “Analisa Pengaruh Kualitas Produk Terhadap Kepuasan Konsumen Menggunakan Metode Kuantitatif Pada CV. Meubele Berkah Tangerang,” Indones. J. Softw. Eng., vol. 5, no. 1, pp. 19–28, 2019.

O. A. Nurkholiq, O. Saryono, and I. Setiawan, “ANALISIS PENGENDALIAN KUALITAS (QUALITY CONTROL) DALAM MENINGKATKAN KUALITAS PRODUK,” J. ilmu Manaj., vol. 6, no. 2, pp. 393–399, 2019, [Online]. Available: https://jurnal.unigal.ac.id/index.php/ekonologi

Y. Hisprastin and I. Musfiroh, “Ishikawa Diagram dan Failure Mode Effect Analysis (FMEA) sebagai Metode yang Sering Digunakan dalam Manajemen Risiko Mutu di Industri,” Maj. Farmasetika, vol. 6, no. 1, p. 1, Oct. 2020, doi: 10.24198/mfarmasetika.v6i1.27106.

D. Christian, A. Sutrisno, and J. Mende, “PENERAPAN METODE ROOT CAUSE ANALYSIS (RCA) UNTUK MENENTUKAN AKAR PENYEBAB KELUHAN KONSUMEN,” J. Online Poros Tek. Mesin, vol. 7, no. 2.

A. Alijoyo, Q. B. Wijaya, and I. Jacob, Failure Mode Effect Analysis Analisis Modus Kegagalan dan Dampak RISK EVALUATION RISK ANALYSIS: Consequences Probability Level of Risk, 2020th ed. Bandung: LSP MKS. [Online]. Available: www.lspmks.co.id

D. A. Kifta and T. Munzir, “ANALISIS DEFECT RATE PENGELASAN DAN PENANGGULANGANNYA DENGAN METODE SIX SIGMA DAN FMEA DI PT. PROFAB INDONESIA DEFECT RATE ANALYSIS OF WELDING AND ITS CONTROL USING SIX SIGMA AND FMEA METHODS IN PT. PROFAB INDONESIA,” DIMENSI, vol. 7, no. 1, pp. 162–174, 2018.

N. Ardiansyah and H. C. Wahyuni, “Analisis Kualitas Produk Dengan Menggunakan Metode FMEA dan Fault Tree Analisys (FTA) Di Exotic UKM Intako,” PROZIMA (Productivity, Optim. Manuf. Syst. Eng., vol. 2, no. 2, pp. 58–63, Dec. 2018, doi: 10.21070/prozima.v2i2.2200.

M. Damaindra and A. S. Cahyana, “PENINGKATAN KUALITAS PRODUK PADA MESIN PRODUKSI NONWOVEN SPUNBOND DENGAN MENGGUNAKAN METODE SEVEN TOOLS DAN FMEA,” Sidoarjo.

A. W. Rizqi and M. Jufriyanto, “| 88-107 JSTI JurnalSistemTeknikIndustri *Corresponding author at: Program Studi Teknik Industri, Fakultas Teknik,” Jl. Sumatera No, vol. 22, no. 2, 2020.

A. Alijoyo, Q. B. Wijaya, and I. Jacob, Root Cause Analysis. Bandung: CRMS Indonesia, 2020. [Online]. Available: www.lspmks.co.id

M. Bahrudin and H. C. Wahyuni, “Pengukuran Produktivitas Kerja Karyawan pada Bagian Produksi dengan Menggunakan Metode Objective Matrix (OMAX) Dan Root Cause Analyze (RCA),” PROZIMA (Productivity, Optim. Manuf. Syst. Eng., vol. 1, no. 2, pp. 116–122, Dec. 2017, doi: 10.21070/prozima.v1i2.1299.

M. T. Fajrin and W. Sulistiyowati, “PENGURANGAN DEFECT PADA PRODUK SEPATU DENGAN MENGINTEGRASIKAN STATISTICAL PROCESS CONTROL (SPC) DAN ROOT CAUSE ANALYSIS (RCA) STUDI KASUS PT. XYZ.”

F. Sepriandini and Y. Ngatilah, “Analisis Kualitas Produk Koran Menggunakan Metode Six Sigma Dan Failure Mode and Effect Analysis (Fmea) Di Pt. Xyz Balikpapan,” Tekmapro J. Ind. Eng. Manag., vol. 16, no. 2, pp. 48–59, 2021, doi: 10.33005/tekmapro.v16i2.203.

R. Saputra and D. T. Santoso, “Analisis Kegagalan Proses Produksi Plastik Pada Mesin Cutting Di Pt. Fkp Dengan Pendekatan Failure Mode and Effect Analysis Dan Diagram Pareto,” Barometer, vol. 6, no. 1, pp. 322–327, 2021, doi: 10.35261/barometer.v6i1.4516.

F. Hendra and R. Effendi, “Identifikasi Penyebab Potensial Kecacatan Produk dan Dampaknya dengan Menggunakan Pendekatan Failure Mode Effect Analysis (FMEA),” SINTEK J. J. Ilm. Tek. Mesin, vol. 12, no. 1, pp. 17–24, 2018, [Online]. Available: http://jurnal.umj.ac.id/index.php/sintek

R. B. Yogaswara and A. Moesriati, “Identifikasi Kendala Proses Produksi Instalasi Pengolahan Air Minum Menggunakan Failure Mode And Effect Analysis (FMEA) (Studi Kasus: PDAM Tirta Cahya Agung Kabupaten Tulungagung),” J. Tek. ITS, vol. 10, no. 2, 2021, doi: 10.12962/j23373539.v10i2.64106.

D. Herwanto, “Analisis Produktivitas Mesin Filling Auto Cup Sealer 1 dengan Metode Overall Equipment Effectiveness pada PT. Prima Kemasindo,” Serambi Eng., vol. VI, no. 4, 2021.

N. Aziza and F. B. Setiaji, “PENGENDALIAN KUALITAS PRODUK MEBEL DENGAN PENDEKATAN METODE NEW SEVEN TOOLS,” Tek. Eng. Sains J., vol. 4, no. 1, pp. 27–34, 2020.

F. Akbar and R. E. Nugroho, “Analysis Relates to the Causes of Damage on the OOG Elevator through Failure Mode Effect Analysis Method,” Int. J. New Technol. Res., vol. 7, no. 5, May 2021, doi: 10.31871/ijntr.7.5.20.

P. Fithri, “SIX SIGMA SEBAGAI ALAT PENGENDALIAN MUTU PADA HASIL PRODUKSI KAIN MENTAH PT UNITEX, TBK,” J. Tek. Ind., vol. 14, no. 1, pp. 43–52, 2019.

Aris Setiawan and Wisnu Pracoyo, “Analisis Kinerja Exhaust Gas Heat Exchanger Dengan Menggunakan Diagram Pareto,” TEKNOSAINS J. Sains, Teknol. dan Inform., vol. 9, no. 2, pp. 83–89, Jul. 2022, doi: 10.37373/tekno.v9i2.196.

A. Irawan, “Boy Isma Putra 2 1,2 Prodi Teknik Industri, Fakultas Sains dan Teknologi,” Univ. Muhammadiyah Sidoarjo Jl. Raya Gelam, vol. 3, no. 250, pp. 20–29, 2021.

Y. Tri Hapsari, “PERANCANGAN STANDAR OPERATIONAL PROSEDUR (SOP) PADA PROSES PRODUKSI FROZEN FOOD,” J. Terap. Abdimas, vol. 7, pp. 8–14, 2022.




DOI: https://doi.org/10.35308/jopt.v10i1.9459

Refbacks

  • There are currently no refbacks.


Copyright (c) 2024 Jurnal Optimalisasi

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

JOPT: Jurnal Optimalisasi Indexing and Abstracting by: